Données techniques
Composants de four
Ces pages réduisent le choix du four, de l'alimentation, des condensateurs, de la tour ou du composant. Les chiffres finaux sont dans le devis.
Bobine d'induction en cuivre refroidie à l'eau pour fours moyenne fréquence
Bobine d'induction en cuivre refroidie à l'eau pour fours moyenne fréquence est fourni aux fonderies qui achètent une fusion qui tient, pas une pièce isolée. Capacité, puissance, fréquence et refroidissement suivent le métal et le réseau.
| Item | Catalog value |
|---|---|
| Conductor | Rectangular copper tube, 99.9% copper |
| US material standard | ASTM B75 seamless copper tube |
| Insulation | Electrostatic spray, high-strength epoxy |
| Insulation withstand | Above 5000 V |
| Turn spacing after fixing | Error not above 2 mm |
| End cooling | Water-cooled turns at the top and bottom of the coil |
| Large coil shown | 60 t medium-frequency coil on the GW sheet |
| Shell on small furnaces | 50 kg–3000 kg aluminum-alloy shell on the same sheet |
| US standard | Applies to |
|---|---|
| ASTM B75 | Seamless copper tube, water-cooled coil |
| ASTM B152 | Copper sheet and strip where used on connections |
| NFPA 86 | Furnace water-circuit safety interlock |
Every figure in these tables is taken from the factory sheets in the product folder and is written in English. 1 metric ton = 1.102 US short tons. Power-supply ratings can still be negotiated to the customer requirement, as the sheet itself states. American standards are the US specifications normally requested with this equipment.
Culasse magnétique pour fours à induction moyenne fréquence
Culasse magnétique pour fours à induction moyenne fréquence est fourni aux fonderies qui achètent une fusion qui tient, pas une pièce isolée. Capacité, puissance, fréquence et refroidissement suivent le métal et le réseau.
| Item | Catalog value |
|---|---|
| Steel | Cold-rolled high-permeability silicon steel |
| US material standard | ASTM A876 grain-oriented electrical steel |
| Sheet thickness | 0.35 mm |
| Shape | Arc matches the outside of the induction coil |
| Clamps | Stainless side plates and stainless tie rods |
| Cooling pipe test | 0.45 MPa, no leak within 15 minutes |
| Duty | Collects stray flux, supports the coil, shields the frame |
| US standard | Applies to |
|---|---|
| ASTM A876 | Flat-rolled grain-oriented electrical steel, 0.35 mm class |
| ASTM A240 | Stainless side plates and tie hardware |
Every figure in these tables is taken from the factory sheets in the product folder and is written in English. 1 metric ton = 1.102 US short tons. Power-supply ratings can still be negotiated to the customer requirement, as the sheet itself states. American standards are the US specifications normally requested with this equipment.
Self de lissage continu pour alimentations moyenne fréquence
Self de lissage continu pour alimentations moyenne fréquence est fourni aux fonderies qui achètent une fusion qui tient, pas une pièce isolée. Capacité, puissance, fréquence et refroidissement suivent le métal et le réseau.
| Item | Catalog value |
|---|---|
| Place in the circuit | DC bus between the rectifier and the inverter |
| First duty | Smooths the rectifier current |
| Second duty | Limits current rise if the inverter sees a short circuit |
| US harmonic standard | IEEE 519, together with 6, 12 or 24 pulse rectification |
| Rectifier | 5th | 7th | 11th | 13th | 17th | 19th | 23rd | 25th |
|---|---|---|---|---|---|---|---|---|
| 6 pulse | 0.175 | 0.11 | 0.045 | 0.029 | 0.015 | 0.01 | 0.009 | 0.008 |
| 12 pulse | — | — | 0.007 | 0.004 | 0.002 | 0.001 | 0.0009 | 0.0008 |
| 24 pulse | — | — | — | — | — | — | 0.0006 | 0.0005 |
| US standard | Applies to |
|---|---|
| IEEE 519 | Harmonic current limits, matched to 6 / 12 / 24 pulse rectifiers |
| NFPA 70 (NEC) | Incoming voltage, grounding and disconnect |
| UL 508A | Control cabinet construction |
| NEMA 250 | Enclosure type for the power cabinets |
| NEMA MG 1 | Cooling-fan and pump motors |
Every figure in these tables is taken from the factory sheets in the product folder and is written in English. 1 metric ton = 1.102 US short tons. Power-supply ratings can still be negotiated to the customer requirement, as the sheet itself states. American standards are the US specifications normally requested with this equipment.
Inverseur de four pour lignes un pour deux
Inverseur de four pour lignes un pour deux est fourni aux fonderies qui achètent une fusion qui tient, pas une pièce isolée. Capacité, puissance, fréquence et refroidissement suivent le métal et le réseau.
| Item | Catalog value |
|---|---|
| Duty | Moves the medium-frequency supply from one furnace to the other |
| Operation | Electric or manual |
| Transfer time | About 20 seconds |
| Contact | High clamping force for the furnace current |
| US standard | Applies to |
|---|---|
| IEEE 519 | Harmonic current limits, matched to 6 / 12 / 24 pulse rectifiers |
| NFPA 70 (NEC) | Incoming voltage, grounding and disconnect |
| UL 508A | Control cabinet construction |
| NEMA 250 | Enclosure type for the power cabinets |
| NEMA MG 1 | Cooling-fan and pump motors |
Every figure in these tables is taken from the factory sheets in the product folder and is written in English. 1 metric ton = 1.102 US short tons. Power-supply ratings can still be negotiated to the customer requirement, as the sheet itself states. American standards are the US specifications normally requested with this equipment.
Câble refroidi à l'eau pour fours à induction moyenne fréquence
Câble refroidi à l'eau pour fours à induction moyenne fréquence est fourni aux fonderies qui achètent une fusion qui tient, pas une pièce isolée. Capacité, puissance, fréquence et refroidissement suivent le métal et le réseau.
| Item | Catalog value |
|---|---|
| Duty | Flexible link from the power supply and capacitor bank to the tilting furnace |
| Construction | Stranded conductor, outer hose, lugs and water ports |
| Supply scope | 1 set included with a GW furnace system |
| US material note | Copper to ASTM B187 where a rigid bus is used instead of the cable |
| US standard | Applies to |
|---|---|
| ASTM B75 | Seamless copper tube, water-cooled coil |
| ASTM B152 | Copper sheet and strip where used on connections |
| NFPA 86 | Furnace water-circuit safety interlock |
Every figure in these tables is taken from the factory sheets in the product folder and is written in English. 1 metric ton = 1.102 US short tons. Power-supply ratings can still be negotiated to the customer requirement, as the sheet itself states. American standards are the US specifications normally requested with this equipment.
Barre cuivre refroidie à l'eau pour condensateurs et sortie four
Barre cuivre refroidie à l'eau pour condensateurs et sortie four est fourni aux fonderies qui achètent une fusion qui tient, pas une pièce isolée. Capacité, puissance, fréquence et refroidissement suivent le métal et le réseau.
| Item | Catalog value |
|---|---|
| Duty | Flexible link from the power supply and capacitor bank to the tilting furnace |
| Construction | Stranded conductor, outer hose, lugs and water ports |
| Supply scope | 1 set included with a GW furnace system |
| US material note | Copper to ASTM B187 where a rigid bus is used instead of the cable |
| US standard | Applies to |
|---|---|
| ASTM B75 | Seamless copper tube, water-cooled coil |
| ASTM B152 | Copper sheet and strip where used on connections |
| NFPA 86 | Furnace water-circuit safety interlock |
Every figure in these tables is taken from the factory sheets in the product folder and is written in English. 1 metric ton = 1.102 US short tons. Power-supply ratings can still be negotiated to the customer requirement, as the sheet itself states. American standards are the US specifications normally requested with this equipment.